New Elkamak VSI DİKMİLLİ KIRICI vertical shaft impact crusher
8997 km to "United States/Columbus"
If you decide to buy equipment at a low price, make sure that you communicate with the real seller. Find out as much information about the owner of the equipment as possible. One way of cheating is to represent yourself as a real company. In case of suspicion, inform us about this for additional control, through the feedback form.
Before you decide to make a purchase, carefully review several sales offers to understand the average cost of your chosen equipment. If the price of the offer you like is much lower than similar offers, think about it. A significant price difference may indicate hidden defects or an attempt by the seller to commit fraudulent acts.
Do not buy products which price is too different from the average price for similar equipment.
Do not give consent to dubious pledges and prepaid goods. In case of doubt, do not be afraid to clarify details, ask for additional photographs and documents for equipment, check the authenticity of documents, ask questions.
The most common type of fraud. Unfair sellers may request a certain amount of advance payment to “book” your right to purchase equipment. Thus, fraudsters can collect a large amount and disappear, no longer get in touch.
- Transfer of prepayment to the card
- Do not make an advance payment without paperwork confirming the process of transferring money, if during the communication the seller is in doubt.
- Transfer to the “Trustee” account
- Such a request should be alarming, most likely you are communicating with a fraudster.
- Transfer to a company account with a similar name
- Be careful, fraudsters may disguise themselves as well-known companies, making minor changes to the name. Do not transfer funds if the company name is in doubt.
- Substitution of own details in the invoice of a real company
- Before making a transfer, make sure that the specified details are correct, and whether they relate to the specified company.
Seller's contacts
+90 537 777...
Show
+90 537 777 87 49
+90 549 473...
Show
+90 549 473 60 62
+90 549 473...
Show
+90 549 473 60 67
Turkey 
Turkey
Feed Material Size, mm - 0-40,
ELKAMAK vertical crushers are tertiary crushers used to crush, cube and produce sand for hard and abrasive materials between 0 and 40 mm.
They are produced in two types as closed and open rotor. Stones with a maximum size of 0-40 mm can be fed to closed rotor crushers. Since the returned material may contain particles larger than these sizes, they are definitely not suitable for crushing returned material.
Vertical crushers break the material fed to the rotor by throwing it at a speed of approximately 67-80 m/s and by hitting the naturally occurring stone box with the stator, stone lining and the material entering the system from the outside of the rotor (stone to stone crushing).
Vertical crushers are used to pulverize materials with a hardness of less than 9 degrees and a moisture content of less than 9%. The materials must be non-flammable and non-explosive minerals.
ADVANTAGES
• Low Cost
• High efficiency and low energy consumption
• High reduction ratio
• Ability to crush hard materials
• Less noise and environmental pollution
• Low maintenance cost and time
Besleme Malzemesi Boyutu, mm - 0-40,
ELKAMAK dikey kırıcılar, 0 ila 40 mm arasındaki sert ve aşındırıcı malzemeleri kırmak, küp haline getirmek ve kum üretmek için kullanılan üçüncül kırıcılardır.
Kapalı ve açık rotorlu olmak üzere iki tipte üretilirler. Maksimum 0-40 mm boyutundaki taşlar, kapalı rotorlu kırıcılara beslenebilir. Geri dönen malzeme bu boyutlardan daha büyük parçacıklar içerebileceğinden, geri dönen malzemeyi kırmak için kesinlikle uygun değildirler.
Dikey kırıcılar, rotora beslenen malzemeyi, yaklaşık 67-80 m/s hızla fırlatarak ve doğal olarak oluşan taş kutuyu stator, taş astarı ve rotorun dışından sisteme giren malzemeye çarparak (taştan taşa kırma) kırar.
Dikey kırıcılar, sertliği 9 dereceden az ve nem içeriği %9'dan az olan malzemeleri toz haline getirmek için kullanılır. Malzemeler yanıcı ve patlayıcı olmayan mineraller olmalıdır.
AVANTAJLARI
• Düşük Maliyet
• Yüksek verimlilik ve düşük enerji tüketimi
• Yüksek indirgeme oranı
• Sert malzemeleri ezme yeteneği
• Daha az gürültü ve çevre kirliliği
• Düşük bakım maliyeti ve süresi